Everybody may have their private rationale involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall surface to remove the old bathtub and position the new tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. See to it you have certified yourself for the task as well as are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to think about using one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bath tub in your restroom if you have currently acquired a new tub and also do not need to change the plan of your previous water system pipes.
Your tools as well as product list should comprise the following:
Planning for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leakages and also tighten them if essential. Fill the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been utilized at the very least when as this will resolve it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to difficulties with wetness and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can split fairly very early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the entire blog posting. Those who appreciated our page plz be sure to share it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Appointment